Considering an ECU remap for your Iveco EuroTech 375hp? A Stage 1 remap can take this All diesel engine from 375 BHP to 435 BHP and from 1700 Nm to 2060 Nm of torque (turbocharged). This engine scores 7/10 for remap suitability. Get a free personalised quote from a trusted remap professional and find out exactly what your Iveco EuroTech can achieve.
The Iveco EuroTech 375hp is a turbocharged diesel engine producing 375 BHP and 1700 Nm from the factory. With a typical Stage 1 remap, output increases to approximately 435 BHP and 2060 Nm — a gain of around 60 BHP (16%) and 360 Nm (21%).
This engine has moderate remap suitability, with gains weighted towards torque — you will notice the difference most strongly in mid-range pulling power and in-gear acceleration. The tuning headroom is classified as moderate, based on the percentage gain available from the factory output.
Considerations: High tuned torque: check transmission torque capacity and service history.
Fuel economy note: possible improvement with conservative driving.
All figures shown are typical estimates based on aggregated Stage 1 data for this engine variant. Actual results depend on vehicle condition, mileage, and the chosen tuning method. We recommend discussing your specific vehicle with a qualified remap professional.
| Engine | BHP | Gain | Torque | Gain | Score |
|---|---|---|---|---|---|
| 240hp | 240 → 290 | +50 | 840 → 1055 | +215 | Good (7.5/10) |
| E24 CURSOR 245hp | 245 → 315 | +70 | 840 → 1055 | +215 | Good (7.5/10) |
| 266hp | 266 → 320 | +54 | 930 → 1140 | +210 | Good (7.5/10) |
| 272hp | 272 → 330 | +58 | 950 → 1170 | +220 | Good (7.5/10) |
| E27 CURSOR 273hp | 273 → 343 | +70 | 950 → 1160 | +210 | Good (7.5/10) |
| 300hp | 300 → 360 | +60 | 1050 → 1300 | +250 | Good (7.5/10) |
| 310hp | 310 → 370 | +60 | 1115 → 1435 | +320 | Good (7.5/10) |
| 352hp | 352 → 410 | +58 | 1280 → 1630 | +350 | Good (7.5/10) |
| E35 CURSOR 352hp | 352 → 410 | +58 | 1280 → 1635 | +355 | Good (7.5/10) |
| 390hp | 390 → 450 | +60 | 1850 → 2250 | +400 | Good (7/10) |
| E40 CURSOR 400hp | 400 → 480 | +80 | 1800 → 2200 | +400 | Good (7.5/10) |
| 430hp | 430 → 495 | +65 | 1900 → 2280 | +380 | Good (7/10) |
| E43 CURSOR 430hp | 430 → 510 | +80 | 1900 → 2300 | +400 | Good (7/10) |
| 470hp | 470 → 540 | +70 | 2200 → 2600 | +400 | Good (7/10) |
Get a personalised remap quote for your Iveco EuroTech. We'll connect you with a trusted professional in your area.
All figures shown are typical estimates based on aggregated Stage 1 data for this engine variant. Actual results depend on vehicle condition, mileage, and the chosen tuning method.
We recommend discussing your specific vehicle with a qualified remap professional before proceeding.
